Diagonal laying of laminate: material calculation and installation features. Laminate diagonally, the pros and cons of laying technology Calculation of the amount of material - how many planks are required

Laminate flooring can be laid in two main ways: straight (along the wall) and diagonally. For narrow long rooms, straight laying is better, and if the length of the room differs slightly from the width, you can resort to diagonal laying. The process itself is quite laborious and requires more complex calculations.

The main disadvantage of diagonal laying is an increase in material consumption (waste is 10-15%, and when laying in a straight line - 5%). But this version of the flooring looks advantageous and allows you to create a more sophisticated design. Since the eye usually glides along the long joints of the panels, this is a good way to draw attention to the piece of furniture located in the corner.

The simplest calculation for diagonal laying is to determine the area of the room and add 15%, and then divide the result by the area of one laminate panel. There is also a formula for a more accurate count.

Let the length and width of the room be X and Y, and the length and width of the laminate panel A and B. In addition to these values, we need a number equal to the square root of 2, which is approximately 1.42.

The area of the room is determined as a standard, X * Y
Stock area according to the formula Y * B * 1.42
To get the total area of \u200b\u200bthe products that will be needed for work, add up both results
We divide the sum by the area of one laminate panel, we get the number of panels, round the result up

In general, the formula for determining the number of panels n looks like this:

Tip: for diagonal laying, it is better to purchase a laminate with shorter panel lengths.

Preparatory work

To cut laminate, you need a tool with fine teeth, it is best to use a special machine or a jigsaw, you can also use a circular saw. In extreme cases, a hand saw or a hacksaw will do, but for a large amount of work, a power tool is preferable. Cutting can be done as the laying is done, first having prepared panels for 2-3 rows. If a large number of panels are cut, they must be numbered so as not to get confused.

Important: the corners in rooms are often not perfectly straight, so you have to navigate directly on the spot to determine at what angle to cut the edges of the panels adjacent to the walls. Especially careful measurements are needed for the first 2-3 rows. If the panel is laid in a place where there is a ledge, a pipe comes out of the floor, curly cutouts are made according to a cardboard template.

Before starting installation, you must:

let the laminate rest indoors for at least a day
level, strengthen, clean the base
lay a substrate
prepare wedges for expansion gaps (you can use wooden bars, laminate trimmings, the optimal width is 1-1.5 cm)

Possible installation options

Laying laminate diagonally can be done in 3 ways:

Laying starts from the corner, the first element has the shape of a right triangle
The first fragment is placed at some distance from the corner and has the shape of a trapezoid
Laying starts from the center of the room, from the line of its diagonal, the first row is prefabricated

As a rule, work is carried out from left to right, starting from the corner farthest from the doors. It is customary to lay the first row with a tongue (crest) away from you, with a groove towards you. Panels with a conventional lock (Lock) are located in the same plane and are knocked out with a light hammer through a wooden gasket for a tight connection. Since it is more convenient to drive a tenon into a groove, and not vice versa, it is better to start laying a laminate with such a lock from the corner and work in one direction. If a row consists of several panels, they can be attached to those already laid one by one or assembled in a row and connected to the previous one.

Clip-on (click) panels connect at an angle and snap into place, no padding required. The connection can be made on both sides, so this laminate can be laid from the center or set back from the corner.

corner stacking

On the reverse side of the laminate board, a right triangle is drawn with 45 ° corners (if the corner of the room is not perfectly straight, the necessary adjustments are made), with the hypotenuse towards the groove. This triangle fits into the corner of the room and wedged from the walls on both sides to form a gap. The unused part of the board will come in handy when laying in the second half of the room.

Then the whole panel is taken, a line is drawn from the edge of the side with the groove towards the side with the tongue at an angle of 45 °. From the obtained point on the side with the tongue, a segment is laid off equal to the length of the base of the triangle. The second point is connected to the base, so that an angle of 45 ° is formed again, an isosceles trapezoid is cut out. The same principle is observed when cutting the following elements - the length of the smaller base of the next trapezoid should be equal to the length of the larger base of the previous one.

When the length of one panel is not enough to fill the distance from wall to wall, rows of several panels are assembled, first from 2, then from more. Corners are cut only at the outer panels in each row. The panels must be laid with an offset of half or a third of the length, so that the seams run apart. Each next stacked row is wedged.
After half the room is covered with laminate, the direction of cutting the corners is changed, now the larger base will be on the side of the tongue, and the smaller one on the side of the groove. At this stage, you can use fragments that were previously formed during cutting.

Video: laying laminate diagonally from the corner

Stacking in two directions

Laying can start with a solid panel, it is cut at both ends at 45°, stacked with cuts parallel to adjacent walls, pushed into a corner as far as the walls allow, wedged. Next, several rows are assembled in the direction of expansion. The next row immediately after the solid panel can be made from two symmetrical fragments, and in the subsequent ones, the seams are shifted. When several rows are collected, you can fill the corner with smaller fragments. For ease of access, the assembled shield can be moved towards you, and when the corner is assembled, push it back, not forgetting the wedges.

If the laying starts from the center, it is necessary to connect the opposite corners of the room with a diagonal line, drawing it on the substrate.

Tip: it is difficult to draw a long line from corner to corner, it is better to pull the cord between nails or self-tapping screws hammered in the corners.

Then the angle between the drawn diagonal and the wall is measured and the first laminate panel is cut at the appropriate angle. It fits into a corner so that its wide base lies on the drawn line, and is separated from the wall with wedges. The required number of whole panels is connected to it at the ends, and the last one in the row is cut at the desired angle. Then the second row is assembled, which is a mirror image of the first, only the cutting must be carried out in such a way that the seams run apart. Further, laying is carried out on both sides of the center, suitable fragments are immediately used.

If the same flooring is laid in several rooms, and they are not separated by thresholds, the laminate is not cut along the line of the doorway, the following panels will be connected to the panels that extend beyond the room.

Video: laying laminate diagonally from the center of the room

Outcome

The laminate, laid diagonally, looks quite impressive, so that the labor and material costs are justified. Laying laminate with a tongue-and-groove connection is best done in one direction and starting from the corner. For snap-on laminate, the laying direction does not play a fundamental role, so new rows can be connected to the base from both sides. When laying from the center, small fragments are mounted last, a more rational consumption of material is ensured.

Reading time ≈ 9 minutes

If you want to create a unique and original design in your apartment using high-quality and affordable materials, try diagonally. Such an unusual way of laying will undoubtedly draw attention to the floor in the room and diversify its appearance. Especially this technique is used in case of incorrect wall geometry or non-standard layout.

Is diagonal styling right for you?

In order for the floor to become a decoration of the apartment, you need to determine exactly which laying technology is right for your interior, diagonal or straight.

Direct styling and its features:

It can be performed in rooms of any configuration with even walls and without any distortions of the box of a residential building.
Recommended for rooms filled with a large number of pieces of furniture, as well as with carpets on the floor. The laminate in this case will not be very conspicuous, so you should not waste time and effort on the original installation. Graceful lines and interesting transitions are simply hidden behind corners and ledges.
The drawing should be laid parallel to the beam of light, so it is recommended to start the flooring from the far door. As a result, lighting will successfully hide gaps and seams between parts, which will make the coating perfectly smooth and glossy. However, this will work if the windows in the room are only on one wall.

Diagonal flooring and its features:

Diagonal laminate flooring is shown in the video below, it is also able to make the unsuccessful geometry of the walls invisible and visually straighten the layout.
The flooring technology in this way is more complicated than direct laying. It is desirable to have experience with the material, so that the result is of high quality and successful.
Laminate should be bought with a margin so that you can safely trim parts. The calculation of the material here is also carried out on an individual basis.

Laminate features:

Laminate panels are easy to lay on the floor in any room, even a beginner can handle it.
A wide range of models of various colors, textures, sizes and styles, which allows you to use this material in rooms with any interior and design.
Modern laminate is a durable and moisture-resistant floor covering that is resistant to abrasion and mechanical damage. It is laid not only in residential buildings, but also in rooms with high traffic, for example, in offices, meeting rooms or conference rooms.

We calculate the consumption of material

First you need to decide on the layout method and decide whether it suits your layout and interior: from what angles should you start laying, and how much waste will remain after trimming the material. Laying laminate diagonally is shown in the video below.
Usually the area of the room is divided by the area of \u200b\u200bthe material in the package and the resulting value is rounded.
Never do the calculation offhand, otherwise the laminate may not be enough. It is also better to buy an extra pack of laminated panels with a margin.

There are two ways to diagonally stack panels:

From the corner, starting from the far window towards the door.
From one corner to another corner. This laying technology is called "deck", as the panels are laid out from the center. Using a special fishing line, it is necessary to determine the diagonal and make markings, and then start laying first to the left up to the corner, then to the right side. The layout process according to this method will be more laborious, but more economical. Since you will need to carefully mark up and more accurately calculate the number of lamellas. Laying laminate diagonally with your own hands is shown in the video.

Stages of diagonal laying

For proper installation, you will need the following tools:

Roulette for measurements.
Ruler and pencil.
Wooden block to knock out the lamellas.
Mallet (carpenter's hammer).
Spacer wedges to secure gaps between panels.
Electric jigsaw.

Foundation preparation

To lay the lamellas, a flat surface is required so that the floor does not deform during operation and the material is not damaged:

Do not forget also about the substrate under the laminate panels. It can be cork or polyurethane, the sheets are laid end-to-end, and it is fixed with a special wide adhesive tape.

Stretch a fishing line, cord or rope between two corners diagonally to fix the direction of the future boards. The fishing line will help to control any slightest deviations from the angle of the lamella flooring. In the interior, diagonal styling at an angle of 45 degrees, but not less than 30, looks most successful.

Layout instructions

Consider in detail two layout methods: from the corner and from the center.

From the corner

Start the installation with one solid board, pre-cutting it at a predetermined angle from both ends. This panel will set the direction for all other details. Also, start work from the corner where the pipes are present, having previously cut holes of the desired diameter in the board.

After mounting the starting lamella, move towards the center of the room. You will be left with a small open corner, which is mounted at the very end. You can cut it from any crop, which will remain in sufficient quantity.

As you move towards the center, do not forget to shift the transverse seams by ½ of the length of the boards. Fasten all elements of the laminate with ends, except for those that are joined to the walls. There should be a distance of 1.5 - 2 centimeters between the wall and the board.

Insert one panel into another and snap into place by lightly pressing on the floor. First you need to connect all the locks on the boards in one row, and then fasten the stacked row with the previous one. If you are working without a helper, use a small weight to help you fix the stack.

It is necessary to cut the extreme lamellas at a certain angle in order to repeat the line of the wall. To do this correctly, you need to measure the distance from the highest point of the row to the spacer peg against the wall, and then from the lowest point. We transfer these distances with lines to the panel, make markings and cut out the desired shape.

From the center

You can use this method only when laying adhesive laminate. In the case of working with panels that have Click-type locks, such a layout is not possible, since some models do not imply a run-up from the center to the sides due to their structure.

The row in the center of the room with the longest panels is laid out first, it will be he who will set the direction for all the other boards. Installation is carried out in a known way, after which we move towards the left and then to the right corner.

After installing all the lamellas, it remains to remove all the bars for spacers and mount the skirting boards.

Laying laminate can be done in any room, the main thing is to calculate the material consumption and take into account the geometry of the walls. In addition, such a floor does not require special care and will serve you for a long time. A video of the master class with step-by-step instructions will help you better understand the technology and understand the intricacies of the process.

Laying laminate diagonally is gaining more and more supporters every day. The advantages of this flooring are known to everyone and everyone, because it is a relatively inexpensive material that looks great in any room. In addition, the installation of the laminate is quite simple and will not cause difficulties even for beginners. It will take only a few minutes to learn how to lay the lamellas correctly, after which the process will go very quickly. But if you want to make the room even prettier and more inviting, try laying out the laminate diagonally. The result will be more than satisfying.

Diagonal laminate flooring - what is its advantage?

The installation instructions that come with the purchase of laminate flooring usually list the easiest installation method. It consists in the parallel placement of boards in relation to the walls. The main disadvantage of this method is that the features of the room itself are not taken into account. For example, rooms decorated in a circle or semicircle will not be very convenient to lay out with parallel planks. In this case, diagonal mounting will help out. With this method, the boards are laid at an angle of inclination of 30 to 45 degrees with respect to the walls, and not parallel to them.

If you figure out how to lay the laminate diagonally, you can hide uneven walls or imperfections in the layout of the rooms. Designers often resort to a similar method to lengthen and expand small rooms. For example, diagonal planks visually lengthen the floor, especially if there is little furniture in the room. Due to this, the room seems more spacious. An important factor when choosing in favor of diagonal laying is that the floor pattern looks much more beautiful and interesting.

The following main advantages of laying laminate diagonally can be distinguished:

If you have uneven walls at home that are also not perfectly parallel to each other, the usual installation method will increase the effect. In the case of diagonal laying, all irregularities almost completely disappear due to the correct texture of the selected material and the desired laying angle of the coating.
Some window openings do not meet standard standards, and this introduces certain changes in the flooring process. If you turn to the help of the diagonals, then the floor will be laid out in such a way that the light falls in the right direction.
With the help of diagonal mounting, it becomes possible to visually stretch and expand the room, emphasizing the originality of the room, focusing exclusively on the unusual and original way of flooring.

Calculation of the amount of material - how many strips will be required?

When installing lamellas in this way, several disadvantages can also be distinguished. So, laying a laminate on a floor diagonally with your own hands is more difficult compared to the traditional method. In addition, you will need a few more consumables. Due to trimming and sawing, you need to purchase 15-20 percent more laminate in advance than you originally planned.

Naturally, you can turn to the help of specialists with extensive experience in this field of home improvement. In this case, the percentage of overspending will not be very large and will not exceed 5 percent. However, the services of professional builders cannot be attributed to the number of cheap ones, so most people try to lay the boards on their own.

Foundation preparation as a necessary stage of work

Diagonal laying, like any other procedure, requires certain preparatory steps. It is necessary to check the load-bearing base of the walls for the percentage of deviation, assess the damage. If possible, try to level out problem areas that can be corrected.

If your floor is concrete, remember that for 2 m 2 the height difference should not be more than 3 mm. Otherwise, you will need to fill a layer of leveling mass or a thin-layer screed. In case of detection of more serious malfunctions of the base, it is required to perform more complex operations related to pouring up to 10 centimeters of cement-sand screed. One way or another, the process of preparing a concrete floor will take a lot of time - up to seven days with small deviations and up to a month if a concrete screed is required.

Differences in the height of a wooden floor can also be significant, but the main problem lies in the design, in which there should be no hidden or visible damage. These include bacterial and fungal infections. For further work, it is required to treat all problem areas with special antiseptics, up to the replacement of individual wooden elements. At the same time, existing elevation differences can be leveled and corrected thanks to various substrates.

Without leveling the base, further work does not make any sense, since the laying of the laminate requires the most even surface. Only in this case, the coating will serve you without the manifestation of deformations, defects and other mechanical damage throughout the entire period of operation, while maintaining all its positive qualities and advantages.

How to do everything yourself and not spoil anything?

When you are done with the preparatory procedures, level and clean the surface, the diagonal laying of the laminate begins directly. There are two main methods:

From the center of the room. You will need to pull the threads from opposite corners of the room diagonally, their intersection is a guideline for installation. The first row should be laid out parallel to the thread, starting from the center to the left.
From the corner of the room. In this case, it is necessary to move towards the door from the window. To make the joints between the plates less noticeable and not attract attention, you can arrange the long end connections of the lamellas in the direction of the light that enters the room from the window.

The process of installing boards is not particularly difficult. First of all, the end locks of the slats are assembled, after which the fully assembled and finished row is combined with the next one. It is much easier to do this when you have a helper. Otherwise, you can resort to some tricks, for example, use not very heavy loads to facilitate the process of snapping the lock joints. It works in the following way: by snapping one part of the row, we put a load on it. After that, you can safely start working with other locks, without worrying that the very first one will disperse.

We recommend laying out the lamellas in a checkerboard pattern. In this case, there should be a distance of at least 40 centimeters between the plates. In this case, the laminate will turn out to be the most durable, strong and reliable, it will withstand loads for a long time without kinks and breaks. Leave a small gap between the boards and the walls, the thickness of which should not be more than 2 centimeters. With humidity or temperature fluctuations, such gaps can compensate for shrinkage and swelling of the laminate.

Another useful observation is the installation of special pegs in the gaps in order to maintain the same distance around the entire perimeter of the room. At the end of the installation, the pegs are removed, and the seams themselves are sealed with skirting boards attached at the junction. The greatest difficulty in the process of laying laminate diagonally is cutting boards. After all, they must be cut perfectly precisely so that the angle fully corresponds to the contour of the wall to which the die is applied. All the same pegs can come in handy here - just measure the length from the top point of the lamella to the peg and in the same way from the bottom point to the peg.

The board must be cut from the back using a regular hacksaw or, ideally, an electric jigsaw. After that, we calmly put the laminate, sawn at such an angle, at which it will fit as tightly as possible with the wall. As you can see, absolutely everyone can lay a laminate diagonally. The process is somewhat more complicated compared to traditional laying methods. A little more source material, planning, preliminary calculations, accuracy and time are needed. However, the result in the form of an elegant and beautiful floor that visually enlarges the room will please you for a very long time.

Laminate flooring, carried out in accordance with all the rules, is always a spectacular result in the form of a beautiful floor. It will not be difficult to make such a laying on your own if you adhere to proven technology. Laying the laminate diagonally requires the same. A little more diligence, patience, time and an unusual approach to a typical floor covering will transform the room, hide its architectural flaws.

Advantages of diagonal styling

In addition to an unusual design solution, the diagonal laying out of the laminate allows you to hide the uneven arrangement of the walls. If they are in relation to each other not at an angle of 90 °, then with such a floor it will be imperceptible. In addition, the diagonal laying of the laminate allows you to visually expand the space of the room. These advantages are relevant for a small room.

Typically, the floor is laid perpendicular to the wall with a window, in which case the light will slide across the floor without highlighting the joints between the boards. Laminate diagonally in the interior of the room, where the windows are on different walls or shifted to a corner, can be the best design move regarding lighting.

The disadvantages of diagonal masonry are the additional costs of the material, and, consequently, the high price of the issue.

Calculation of the amount of laminate

Laying laminate diagonally requires more consumables. The fact is that the panels will have to be cut from the ends at an angle, which leads to an increase in waste. If the flooring is installed independently for the first time, then it is better to play it safe and purchase material 10-15% more than the norm. Although professionals make a margin of 5%.

Before laying the laminate diagonally, the number of panels is calculated using the following formula: the floor area is multiplied by 1.1, i.e. the amount of laminate will increase by 10%. If the resulting number is divided by the area of one laminated board, then you can get the exact number of panels needed to repair the floor.

Experts advise buying the necessary material in full.

How to lay the laminate diagonally with your own hands - step by step instructions

Since the store may then not have the desired color, and shades from different manufacturers are different. Even shades from the same company, but in different batches, may not be suitable.

Preliminary work

We prepare the floor

Before laying the laminate diagonally, and in general in any way, you should check the floor for stability and evenness of the surface. Floorboards should not sag under the weight of a person, should not creak.
You can lay laminate on a concrete floor, on linoleum, wooden floor, parquet, etc. before that, you need to lay it with a special substrate.
If the old coating sags or creaks, then these shortcomings should be eliminated by carrying out the necessary repair work. It may be necessary to open the floors and align the logs.
Linoleum, which was decided to be left under the new laminated coating, should also be without obvious flaws in the form of swellings, delaminations, holes. Otherwise, the panels will not lie flat or will sag and deform over time.
Before laying the laminate on concrete, the concrete surface is coated with a waterproofing agent. After that, a plastic film is laid on it.
Under the laminated coating, the substrate must be covered. It can be polyurethane foam or natural cork. Regardless of its naturalness, the sheets of the substrate are laid butt-to-joint and fastened with adhesive tape.
OSB boards make it possible to perfectly level the floor surface and additionally isolate the room from noise and save heat in the room.

Preparing tools and materials

After purchase, the panels should be unpacked and left to "lie down" for 2-3 days. Thus, the material will take the optimal parameters (temperature, humidity, plasticity), which will exclude its deformation after installation.

To lay the laminate diagonally with your own hands, you will need some tools:

fine-toothed hacksaw or electric jigsaw;
a hammer with a nozzle made of wood or rubber;
special curved mount for mounting near-wall elements;
measuring instruments: tape measure, ruler, square with an angle of 45 °;
pencil or water marker.

In addition, wedges 1 cm thick will be required, which will not allow laying the laminate tightly against the wall. Instead of wedges, you can use trim panels, inserting them between the board and the wall.

Choose an angle

Laying the laminate diagonally with an angle of 45 ° is considered optimal. At the same time, less material waste remains, because. trimmings will be well suited for use in other masonry areas.

A smaller laying angle obliquely up to 30° is possible. With a lower indicator, the coating will not look aesthetically pleasing, giving the impression of an imbalance in the interior.

Floor installation

The layout of the panels starts from the far corner of the room or from its middle - these are the main ways of laying the laminate diagonally. The strength of the floor is increased by laying the panels in a checkerboard pattern or like a brick wall. Before laying the floor diagonally, you should draw a work plan, given the scale. This will avoid blunders, and the laminate floor will turn out perfect.

The laying of the laminate diagonally is clearly shown in the photo and video.

From the corner

Further laying depends on how the first panel is laid correctly:

The first to put should be a whole panel, trimmed on both sides at the right angle. At the same time, the corner of the floor itself remains open, it is laid at the end of installation, filling it with suitable trimmings. Laying the floor should be from the far corner in relation to the door.
Further, the panels are joined to each other, and the gap between the masonry and the wall is strictly observed throughout the work.
The new row is installed in its place, but is not finally fixed, the panels are docked only at the ends.
The end panels are the last to join the row, after they are cut to the required length, taking into account the centimeter gap.
When all the details of the row are ready, they are removed from the lock, finally joined from the ends and the entire row is engaged with the previous row. This stage is more convenient to carry out with an assistant.

If all corners of the room are perfectly correct, i.e. have a value of 90 °, then the trimmings will be great for subsequent rows. At the same time, material consumption is noticeably reduced, and, consequently, the cost of repairs is reduced.

From the center

Before laying the laminate diagonally, starting from the middle of the room, a long row is assembled according to the method described above. Those. first, whole panels are assembled in a row, then the extreme elements are cut at the desired angle. The entire row is joined at the ends and laid in the center of the room. The next row is also assembled and interlocked with the first.

The further scheme of laying the laminate diagonally is carried out alternately, first in one direction to the corner, and then in the other direction.

This method is especially appropriate if there are external corners (ledge, column, transition from one room to another). When laying adhesive laminate, take a three-hour break after the first three strips to allow the adhesive to set. If the laminate has CLICK locks, then the "from the center" method is not possible due to the characteristics of the adhesion.

At the end of the installation of the floor, install the plinth. They are attached to the wall, but not to the floor.

Dear visitor! You are in the archive of the old mastergrad.com forum

How far away from the wall should laminate flooring be?

Diezel Aug 6 2004 09:20:50	Please tell me how to lay the laminate correctly, in the sense of what distance from the wall to the laminate is considered correct? As I understand it, the laminate should "breathe", i.e. will expand / contract and it is necessary that the wall is not an obstacle to it. The search didn't help. And in general, how much does it shrink in winter or expand in summer? Laminate on locks 22-23 class.
Joker (Taganrog, Russia) Aug 6 2004 10:13:53	It should be in the instructions. If not, here are the instructions for KronoFlooring laminate: http://plastik.nm.ru/montag/laminat_m.htm And another article on the topic of laying laminate: http://www.stroycity.ru/product/parket_ukl_bezkley.html
Diezel Aug 6 2004 10:42:23	Joker, the link to Stroycity is broken - there are no articles ... 🙁
Diezel Aug 6 2004 13:57:18	As I understand it from the first article - there should be wedges between the wall and the laminate - it turns out 15 mm. Is everything right? Do the wedges prevent the laminate from subsequently "breathing"?
Anton (moscow, russia) Aug 6 2004 14:08:25	And subsequently wedges should not be. You need to take them out.
Diezel Aug 6 2004 14:09:58	After assembly, then take it out, on top of the plinth? Is 15mm up to the wall okay? Are skirting boards attached to the wall in this case?
Diezel Aug 6 2004 14:11:25	And another question: during assembly, should the wedges be on the side of the laminate board and on the end? Or just on the side?
demand Aug 6 2004 16:36:53	in my opinion 1.5mm per meter of room width
Anton (moscow, russia) Aug 6 2004 17:41:54	The gap is calculated according to the instructions for the laminate per unit of length and width (different along and across). In a room of normal size - no need to fool your head: 15mm around the entire perimeter is enough. If the walls are perfectly even, then just along the wall you can put laminate trimmings in 2 layers (8 + 8 = 16mm). Since the walls are always curved, stepped wedges are used to adjust the gap. Laying laminate diagonally with your own hands - VIDEO They are needed from those sides where you will push the board, collecting it into the castle. Otherwise, just the entire plane of the floor will leave. After laying the 20 sq.m. room and removing the wedges, I easily moved the entire floor to even out the gaps. Naturally, the skirting boards are then attached to the wall.
Serg (Samara, Russia) Aug 7 2004 01:05:53	2Diesel: > Are skirting boards attached to the wall in this case? Skirting boards are always attached to the wall. Best regards, Sergei
Diezel Aug 9 2004 08:39:34	Thanks everyone for the replies!
Joker (Taganrog, Russia) Aug 10 2004 10:19:35	The link is normal (it is in the favorites), it looks like it was just nailed :(( When attaching the baseboard, do not pinch the laminate too much, otherwise your gaps will not help it.

Features of the laying process

smoothing uneven walls;

also laying can be done from the center.
Laying laminate diagonally: technology and nuances of diagonal installation

To do this, a cord is pulled through the center diagonally between opposite corners of the room. Laying is carried out parallel to the cord with a gradual removal from it to the sides.

Features of the laying process

The biggest difficulty for novice workers is the stage of cutting laminated panels, which must be placed against the wall. The bottom line is to cut at an angle, while completely repeating the outline of the wall. The pegs help in this, by which the near and far points on the panel are determined, connected by a line and cut from the inside with an electric jigsaw.

Outcome

The basics of laying laminate at an angle
The advantage of diagonal laying
Calculation of the amount of laminate for laying
Beginning diagonal laminate flooring
Features of the laying process

Laminate is gaining more and more popularity as a floor covering, which many owners not only buy for the interior of rooms in their homes, but also strive to install it on their own without involving specialists from construction companies. The article will discuss how the diagonal laying of the laminate with your own hands is carried out no worse than that of professionals and what are the features of this process.

The basics of laying laminate at an angle

A common thing for many owners of their own homes is to buy a laminate and lay it exactly according to the instructions on the package, but there is no elegance and zest in such a coating. No construction company will present photos of such flooring as an advertisement for their own services, since they do not attract potential customers.

It is reasonable to use this method only in cases where certain conditions of the room require laying boards butt-to-butt and not otherwise.

If the room has some layout flaws, or vice versa, the designer’s idea (rounded walls or characteristic projections of the floors), then the option will look aesthetically pleasing when the laminate is laid at an angle to the walls.

Traditional flooring installation involves laying planks parallel to one of the pairs of walls. Diagonal laying implies observance of an angle from 30 to 45 degrees. The angle is selected depending on what angle is observed at the junction of two walls. See also: "Which laminate layout is best suited for a room."

The advantage of diagonal laying

Usually do-it-yourself diagonal laminate flooring is done because it is original. But, nevertheless, laying a laminate diagonally has its pros and cons and it is necessary to take them into account before purchasing materials and starting work.

We are talking about the following advantages of technology:

hiding various layout flaws;
smoothing uneven walls;
visual expansion of space in very narrow rooms with a lack of natural light;
naturally, the diagonal arrangement of laminated panels is much more beautiful.

Actually, you can experiment with a similar laying method if there is enough time and money for this. For example, designers, taking into account the latest fashion trends, like to make room zoning, combining a variety of colors and textures, or joining different floor coverings. See also: "How to lay a laminate along or across - the choice of laying method."

Calculation of the amount of laminate for laying

Before laying the laminate diagonally, it is necessary to correctly calculate the amount of material in order to carry out installation without additional purchases and overpayments. Diagonal laying implies increased costs, because the laminate is purchased not to spare, but 15-20 percent more (for waste). If earlier the owner had experience in laying such a coating, then you can make a stock of only 5-10 percent.

Beginning diagonal laminate flooring

Naturally, laying laminate at an angle, like any other coating, can only be done after careful preparation of the subfloor: leveling and cleaning from dust, dirt, debris, liquid, etc.

You can start the installation process:

from the far corner of the room, located opposite the front door. This is done so that the joints of the planks (on the long sides) are located along the sunlight entering the room through the windows. Thus, joints can be made less noticeable, which makes the coating more aesthetic in the photo and visually increases the space;

Features of the laying process

First, a row of panels is assembled into one solid long structure by snapping the lock fasteners. Then he joins the already laid row. Before laying the laminate diagonally, you should find an assistant who will help at least at the initial stage, since the longest rows will pass through the center and it is quite difficult to combine such rows with each other.

Without an assistant, the procedure is performed using a small weight. First, several panels are snapped into place, and a load is placed in some place so that when working on the remaining part, the previous section does not disperse. See also: "How to lay a laminate - do-it-yourself laying sequence."

Laying, as in the case of the usual parallel version, must be carried out with some divergence of the ends of the boards. Each row should be shifted by about 30-40 centimeters, as is the case with the installation of a ship deck. This condition is required to increase the strength of the coating.

In addition to laying the laminate diagonally correctly, some features of this coating should be taken into account. We are talking about a possible change in the size of the flooring due to fluctuations in temperature and humidity in the room. Each specialist will say that it is necessary to create an expansion gap between the laid laminate flooring and the walls.

The width of such a gap should be from 1.5 to 2 centimeters, and then the coating will definitely not be deformed due to an increase in temperature or air humidity. In order to maintain the distance from the laminated panels around the perimeter of the room to the walls, you should use special pegs or small bars that you can make yourself. Upon completion of the work, they are taken out. The gaps themselves will be covered with decorative plinths.

Of course, the diagonally laid laminate has disadvantages, but they are commonplace: the high complexity of the work being done and the high cost of materials (taking into account the fact that you need to buy more). Increased laminate consumption when laying diagonally can be eliminated if you seek help from a laying specialist, then material overrun can be reduced to 3-5 percent.

Laying laminate diagonally with your own hands (photo)

The pegs help in this, by which the near and far points on the panel are determined, connected by a line and cut from the inside with an electric jigsaw.

The points are determined by measuring two distances:

from the top corner of the row to the inserted peg;
from the bottom corner of the row to the inserted peg.

Then, points are set at the same distances from one and the other part of the bar.

Outcome

The article describes in detail how to lay a laminate diagonally, what are the main advantages and difficulties of this process. If the owner wants to get a high-quality and organic looking coating in his own home, then this method is the best fit. See also: "How to lay a laminate - a sequence of actions."

Do not forget that any difficulties will be overcome by professionals from a construction company who can take responsibility not only for laying, but also for choosing a floor covering, taking into account the basic wishes of the owner.

The basics of laying laminate at an angle
The advantage of diagonal laying
Calculation of the amount of laminate for laying
Beginning diagonal laminate flooring
Features of the laying process

The basics of laying laminate at an angle

It is reasonable to use this method only in cases where certain conditions of the room require laying boards butt-to-butt and not otherwise.

The advantage of diagonal laying

We are talking about the following advantages of technology:

hiding various layout flaws;
smoothing uneven walls;
visual expansion of space in very narrow rooms with a lack of natural light;
naturally, the diagonal arrangement of laminated panels is much more beautiful.

Calculation of the amount of laminate for laying

Beginning diagonal laminate flooring

Naturally, laying laminate at an angle, like any other coating, can only be done after careful preparation of the subfloor: leveling and cleaning from dust, dirt, debris, liquid, etc.

You can start the installation process:

from the far corner of the room, located opposite the front door. This is done so that the joints of the planks (on the long sides) are located along the sunlight entering the room through the windows. Thus, joints can be made less noticeable, which makes the coating more aesthetic in the photo and visually increases the space;
also laying can be done from the center. To do this, a cord is pulled through the center diagonally between opposite corners of the room. Laying is carried out parallel to the cord with a gradual removal from it to the sides.

Features of the laying process

The biggest difficulty for novice workers is the stage of cutting laminated panels, which must be placed against the wall.

Laying laminate diagonally: photo, video, diagram

The bottom line is to cut at an angle, while completely repeating the outline of the wall. The pegs help in this, by which the near and far points on the panel are determined, connected by a line and cut from the inside with an electric jigsaw.

The points are determined by measuring two distances:

from the top corner of the row to the inserted peg;
from the bottom corner of the row to the inserted peg.

Then, points are set at the same distances from one and the other part of the bar.

Outcome

Calculation of laminate when laying diagonally

Tool and preliminary operations

Diagonal laminate flooring

Video of laying laminate diagonally

Photo of laying laminate diagonally

Calculation of laminate when laying diagonally

Many mistakenly believe that the consumption of laminate when laying diagonally is uneconomical, has a lot of waste and will require advance purchase of material with a huge margin. Having correctly approached the task, it is enough just to purchase a laminate in an amount that exceeds the area of \u200b\u200bthe room by 5-15%.

Tool and preliminary operations

For such styling, the same tools are used as with the classical one: a hacksaw, a tape measure, a bar, a ruler, a hammer, a pencil. Preliminary operations consist in trimming the solid base, cleaning it from dust, laying the substrate and arranging the spacer wedges.

Diagonal laminate flooring

It should be understood that laying diagonally does not require an exact angle of 45 degrees, it can be from 30 to 45. To hide the joints, the panels must be positioned so that the long seams coincide with the direction of the sun's rays falling on the coating.

The required clearance from the wall is 10 mm. Laying laminate diagonally can be started in two ways. The first involves laying the very first panel in the corner of the room, and then move from the window towards the door. In the second method, the thread is stretched between two corners and, focusing on it, the first row of the laminate is mounted.

It is necessary to accurately measure the last of the panels, while noting the cut line on both sides, do not forget to observe the required size for the gap. With the standard laying method, the cut piece is used for the next row.

Do-it-yourself diagonal laminate laying technology

But for diagonal laying, a huge piece would have to be cut off in order to make a new corner. To save material, you simply set aside the cut piece for use in the opposite corner.

The most economical option is laying, which starts from the middle of the room and is directed to the left corner with respect to the incident light rays. For a correct idea of the future location of the panels in the room, definitions with a pattern and an understanding of material consumption, experts recommend estimating on paper a scheme for laying a laminate diagonally.

To begin with, the panels are laid on the left side, after which, on the right, but the first line must be directed to the left corner. The lock laminate is immediately connected with end locks, and then with the next row. Each row is staggered, while maintaining a size of 30 cm between the end joints. In order to avoid bouncing of the panels, any of the edges of the neighboring row is pressed down with a load.

At the final stage of laying, the expansion wedges must be removed. The gap that has formed between the laminate and the wall is covered by the installation of a skirting board, which is attached exclusively to the walls.

With a video and photo of laying a laminate diagonally, you can read in detail a little lower in our article.