Uniclic multifit: innovative locking connection. Which laminate is better choice of Click locks with aluminum plate

Laminate lock is the most important indicator of quality; the overall appearance of the coating largely depends on its performance. The presence of a good lock will allow you to get closer to the answer to the question: “which laminate is better”.

Patented by Quick-Step. The locking system is very convenient when laying laminate in doorways, corners and in confined spaces. The board can be snapped either by the standard method, at an angle of 25-30 degrees, or by laying the board completely on the floor, by padding.

Another indisputable advantage - the ability to stack and snap boards both on the left and on the right, is important in a complex configuration of the room. The boards snap into place very easily, with a characteristic clear click. Treatment against moisture penetration, present.

According to the manufacturer, the system allows you to repeatedly disassemble the boards without damaging them. In his fifteen years of practice, the only time I encountered the desire of the customer to remove the old laminate and transfer it to the country house. In any case, the laminate deforms during operation and takes on uneven floors, assembly in a new place is possible, but it will no longer be of such high quality, even if the boards are numbered. The declared function is useful, first of all, during the usual laying by a novice master, when repeated separation of the boards during the fitting process is inevitable.

After assembly, the surface is perfectly smooth without the slightest difference in height and gaps. A small minus of this type of lock is the ability to diverge along the short side of the boards. It is connected with a very small protrusion of the latch from below, seen in the photo.

LockT-lock and 2-lock

It was produced and is still found on sale by the Tarkett concern (a new lock is replacing it). A characteristic feature is that a large angle of elevation of the board is not required during installation, an angle of 20 -25 degrees is enough. T-Lock is well-known, but at the same time, quite old, it requires the assembly of the entire series. For one person, this is a time-consuming task, and sometimes impossible. With the length of an ordinary room of six meters, the slightest shift of any panel at the end joint, to the left or right, will require disassembly of the entire row. Also, transverse joints are often visible,

Moreover, this feature is observed in different collections. This defect is most noticeable on collections of dark tones. During installation, you can feel the moment when the board sat down in place, although not as clearly as with Quick-Step. In our work, in the vast majority of cases, a laminate with a thickness of 8 millimeters is used, for longitudinal locks, the protrusion is rather weak - often, when it is snapped again, it breaks off. Moisture protection proprietary - Tech3s.

The 2-Lock lock has a plastic insert, provides high assembly performance, plus the ability to work alone.

Lock - TC'Lock

Lock from TARKETT, which replaced the T-Lock. As sales progress, all laminate collections are transferred to a new lock, and without any increase in price. The old and new locks are not compatible, there will be a difference in height of about 0.4 mm.

The manufacturer claims a tighter connection of the boards, which significantly increases the protection against moisture ingress. The tear test showed a result eight times higher than the parameters laid down, according to the EN13329 standard, which can significantly reduce the number of chips, the divergence of the boards. Boxes with a new lock are marked accordingly. From personal experience, a laminate with such locks is going great. Fixation - without any effort, the installation speed is significantly increased. Assembly can be done by one person.

Lock -

From the manufacturer Classen. A plastic insert is installed at the end of the board, which allows you to snap the board in place by simply pressing on the board from above. Provides a very strong mechanical connection. Work with a vacuum cleaner! The main advantage is the laying speed, unlike standard methods, it is not required to collect one long strip, which allows one person to work comfortably, without outside help. Very high quality factory protection against moisture.

Pergo PerfectFold 3.0 locking system

A variety of locks with a plastic insert. Very easy assembly process. Assembly can be done without a partner. No additional tool is required. Convenience and speed of installation, has a downside - repeated disassembly leads to breakage of the lock combs. It must be collected immediately, without errors. You should be wary of "self-confident masters." The lock looks similar to the Uniclik system, which entails the temptation to knock something out, knock on something, and so on. The result is inevitably damaged locks.

A characteristic, soft click will notify you of the correct installation. Assembly is possible from different sides of the boards, both from the crest and from the groove. Actual when assembling floors without thresholds.

No complaints were found during operation.

Lock -Proclic andJustclic

From the manufacturer Egger, good locks, Pro does not require the assembly of the entire row, the board is besieged from above with a fist. High assembly speed.

Just-clic came to replace him. Unlike the old one, it requires a complete assembly of the row during installation. The profile of the lock in the form of an oval follows the contours of the tongue and groove with minimal gaps. Very accurate lining of the castle elements, requires perfect cleanliness inside.

Purely subjectively, I liked the first option more, fixation, without a pronounced click, although in both cases, there are no complaints. The surface is perfectly flat.

Lock -twinclick

Russian manufacturer Kronospan. Virtually indistinguishable from Tarkett's T-lock. It allows you to assemble the laminate only in a standard way, in whole rows, it is better to work together. The quality is at the level of the middle price category, without differences in height and gaps. When assembling, there is no feeling of a clear fixation of the lamella. Quite difficult work in doorways, the method for fitting under the door frame, by cutting off the comb of the lock, is relevant in inconspicuous places. With this type of lock, it is difficult to achieve high-quality styling by the now common method “the whole apartment without thresholds”. On well-lit surfaces, all tricks, in the form of a cut-off lock, will be noticeable, which is fraught with rapid wear of the protruding part.

Locks in inexpensive collections do not hold moisture at all, it is necessary to treat them with Click Guard sealant. Today, this is already nonsense, given the cost of the sealant and the laboriousness - it is better to choose the option with a waterproof lock.

Lock -Alloc

From a Norwegian manufacturer, a very high-quality lock with an aluminum insert, does not have any advantages for ordinary apartments, its main advantage is a strong mechanical connection that can prove itself in large areas where a conventional laminate requires the installation of dividing thresholds. Ease of installation and a clear fixation is a plus. The price is minus. Compared to the same Classen, given the huge selection of colors for a small apartment, the purchase can hardly be called expedient.

Conclusions:

In this article, only those locks with which our masters work constantly are described, there are a huge number of different trade names, but the essence remains the same. Glue padlocks are a thing of the past. Modern locks that allow you to work without glue and sealants are well developed and reliable, provide high quality and durability. The only difference is the ease of installation.

Contrary to the statements of the manufacturers, the possibility of laying coatings without the use of additional tools, upsetting boards using a bar or a piece of a lock from another lamella is always required! Light sampling of gaps should be carried out necessarily. .

Given the allowable micron gaps, laying work, with any type of lock, should be carried out only with the use of a vacuum cleaner. Dust removal of the groove, under the next row, is also required!

A laminate that requires laying in a row, it is advisable to lay it with a partner, alone, it is easy to break the lock, this manifests itself in the form of a gap and a characteristic elevation in the transverse joint.

All well-known manufacturers in Russia produce laminate in accordance with GOST or TU, often similar to European standards. As a rule, a difference of up to 100 microns is allowed - this is the thickness of a sheet of paper "Snow Maiden". Tactilely, such a difference will be felt when held with a fingernail, and will be visually visible, although it is considered the norm.

You should not buy a laminate without moisture protection of locks, this is no longer relevant, the difference in price is negligible, and the service life differs significantly.

The craftsmen who work for us note the successful design of Quick-Step Uniclik locks, which allow laying laminate in “difficult places” with minimal damage to the lock, and experience in operating coatings from the same manufacturer allows us to give it an “excellent” rating. Preference for Belgian-made laminate, Russian Quick-Step, with quality, yet, not everything is so smooth yet. There is no ease and clarity of assembly. The Uniclic lock is used by the Kastomonu concern, which produces laminate in the city of Yelabuga. The rating "good" honestly deserves the new TC-Lock from TARKETT.

There are several types of locks for assembling a laminate, differing in the design of the connecting elements. Many manufacturers themselves develop locking systems and use them in their floors, and some use previously developed and patented systems.

Smart lock

The SmartLock double locking system of Pergo laminate is the simpler method of the ProLoc system. SmartLock has connecting joints endowed with a special moisture-proof impregnation. The use of joint joints in combination with a highly moisture resistant backing provides Pergo laminate with an additional level of protection for high density fibreboard floors. Boards withstand the strongest operational loads of any severity. The SmartLock system allows you to quickly and easily install your laminate flooring for a superior end result.

ProLoc lock

In residential construction, Pergo applies the principle of ProLoc locks, taking into account the corresponding high requirements of this sector. This is a quick and fairly easy way to install laminate panels, giving a great final result. The ProLoc system meets the high technical requirements for commercial floors that are installed over large areas and carry heavy loads. The technology is patented and is one of the most reliable floor coverings on the market. Designed for the professional market, it uses a revolutionary triple mounting system made from stronger and safer parts. Installation remains as easy and fast as any other system. ProLoс is equipped with connecting joints with a special moisture-proof impregnation. In combination with a base with high moisture resistance, additional floor protection is obtained. For areas with an increased need for moisture protection, Pergo has released an advanced SafeSeal sealant. Together with the ProLoc system, it provides the perfect moisture-resistant connection.

PROClic lock

Egger pleases us with the new PRO Clic interlocking technology for laying laminate. The special geometry of the Egger profile ensures that one element is laid, which facilitates installation - the laminate is laid quickly and easily. The indicators of all qualities of the floor have risen - the degree of stability, high stability under large point loads, strength under surface pressure. It became possible to lay laminate with the help of special sealants STRIP EX and CLIC SEALER, eliminating the use of tools. In 1996, the company used the tongue-and-groove type and adhesive technology. Then she successfully introduced the locking (click) method. The connection became strong. At the moment, there has been a transition to the Just Clic System (form connection). It is also possible to combine two types of Pro Clic System connection technologies.

ClickXpress lock

Variety of sizes, colors and textures. This is not limited to the choice of laminate flooring. An additional factor in deciding whether to purchase a particular material may be the connection system. Consider the most popular types of laminate locks that provide the necessary technical requirements for laying. We will also figure out which locking system is best suited for each specific case. And finally, we will give a few recommendations for installation and maintenance.

Several decades have passed since the creation of such a coating as a laminate. During this time, technology has changed a lot, this also applies to locks. Every 2-3 years, manufacturers introduce a new type of connection, arguing this with improved stability and ease of installation. However, each prototype comes down to two basic ones: Lock and Click. Let's consider them in more detail.

The most popular collapsible systems that have won the recognition of laying masters. For each of these types of castles, there are many subspecies. Some of them can be found only in individual manufacturers, while others, on the contrary, are in service with most well-known laminate manufacturers.

Both basic systems are based on a tenon-and-groove connection. The difference is only in the profiling of the connecting parts.

Which lock is better Lock or Click

We will make a comparison according to the characteristics that are most relevant for the buyer.

cheaper;
tight connection.

with prolonged use (with a deviation from the installation and operation standards), gaps between the lamellas may appear;
a more complex laying process using a mallet and a padding strip;
the risk of damage to the lock during installation.

ease of installation;
installation is made without additional tools;
increased strength;
during operation, the lock does not wear out, cracks do not appear;
a tight connection is ensured when using double locks;
the possibility of mounting on an imperfectly flat surface;
safe assembly with minimal chance of damaging the lock;
the possibility of re-coupling after dismantling the coating.

high price.

Let's take a closer look at the pros and cons of both systems below.

Lock locks

Translated from English, the name of the compound is translated as "castle". This method of fastening laminated panels is one of the very first. At present, this type of surface closure is technologically obsolete.

On the one hand, the mating surfaces are a groove, on the other hand, a spike, which are cut by a cutter on the bearing layer of the board.

The installation principle is as follows:

An attached board is attached to the board located on the floor at an angle of 0 °.
A padding bar is substituted for the opposite side of the lamella.
With light blows of the mallet on the bar, we achieve tight contact until the gap is eliminated.

Advice: tamping should be done carefully, without any extra effort, since with strong blows with a mallet, there is a high probability of damage to the lock.

If the connection is correctly installed, the stud fully enters the groove, the comb fixes it into the stud in the recess and prevents the adjacent panels from coming out of the hitch. This type of lock is also called a lock.

The weak link in the design is precisely the comb, which takes most of the stress on itself. The connection between the groove and the thorn is quite tight, however, with frequent loads on the lock, the comb is abraded. In the future, cracks appear at the attachment point. This defect cannot be eliminated without dismantling and subsequent replacement of the panel.

But this defect can be prevented. To do this, it is necessary to install the laminate on a perfectly flat surface with the elimination of the smallest particles of construction debris and the use of a substrate material that will not give a strong subsidence during operation. Otherwise, any "pebble" under the coating will create additional stress in the castle, reducing the life of your flooring.

Otherwise, even though the technology is outdated. This type of laminate lock provides all the necessary performance properties, subject to proper installation and further use. However, manufacturers prefer the Click system, so finding the “old version” is becoming increasingly difficult (if we are talking not about Chinese fakes, but about certified manufacturers).

Click locks

A relatively new technology, according to which the panels are fixed by means of snaps. The main distinguishing features from Lock, apart from the installation method, is a different shape of the tongue with a groove profiling for it.

The spike is also located on the carrier plate and looks like a small hook.

The installation method is as follows:

A panel to be mounted is brought to the board laid on the floor at an angle of 45°. The angle may vary from manufacturer to manufacturer, so this point needs to be clarified.
The hook is driven into the groove.
The panel is lowered to the horizontal.
A characteristic click is heard, the connection is made.

It is because of this click that the system got its name.

There is no need for additional tools during installation. You don’t need to make special efforts, finish it off with a mallet or hammer too. Otherwise, the key edge may be damaged.

Note: if, when fixing the plank, a small gap remains, then to select it, it is necessary to lightly tap with a mallet on a previously substituted bar or other laminate board. This must be done carefully so as not to spoil the lock element.

This type of connection is characterized by good density and operational properties - the retaining edge in the groove practically does not wear out over time. Therefore, such a laminate will last a long time without the appearance of gaps and cracks.

Also, the canvas assembled by the Click system can be reassembled. However, it is worth considering that during the life of the laminate takes on the smallest unevenness of the floor, and in a new place the adhesion may not be so tight, even taking into account the numbering of the boards.

The Click method does not require such strict restrictions on the evenness of the surface on which it fits (unlike Lock), but this does not mean that the base does not need to be leveled. An even base for laminate is a prerequisite for installation.

Let's consider several subtypes of the Click system, which are the most popular.

Uniclic

It is mainly represented by the Quick Step brand. Installation can be done by simple snapping - for this it is enough to bring one panel to another at an angle of 25-30 ° and fix it. There is also the possibility of laying horizontally with joint padding, for laying in the last row.

It has fairly good strength properties. Withstands a tensile load of up to 450 kg per linear meter.

System advantages:

the lock snaps into place without much effort;
reassembly is possible;
laying both from left to right and from right to left;
moisture treatment.

Minuses:

over time, the lock may disperse along the end of the bar due to the low ridge in the groove.

JUST clic and UNI fit

Patented systems under the Egger brand.

JUST click replaced Pro clic. Unlike its predecessor, assembly of the entire series is required. The bar has two identical tongues and two identical grooves, which makes it possible to engage on both sides. It has a high assembly speed.

The groove and spike are profiled in the form of a conjugated oval, in connection with which a tighter contact is provided over an increased contact area. The gaps in the lock are minimal, so even the smallest debris is not allowed - check the strips before mounting.

Lamel with a lock UNI-fit can be fixed to the previous row separately, that is, it is not necessary to assemble a whole row for subsequent fastening. The spikes and grooves on the end and the long side are different.

SmartLock and ProLock

Both options are presented by Pegro. SmartLock is a more primitive version in terms of profiling - there is one additional retaining element on the top of the slot missing. As a result, a lower contact density is observed.

Most modern Pergo laminate models are equipped with the ProLock system. Both types of locks have a moisture-repellent impregnation, which, coupled with a massive fibreboard base, makes this coating well protected from moisture (sealants are used for even better protection).

ClickXPress, DropXPress, PressXPress

Represented by the brand Balterio.

ClickXPress represents a bunch of groove-thorn with a profiling of the lower part in the form of an oval conjugation. Laying is done at an angle of 45°.

The advantages of this connection include:

reliability;
strength;
imperceptible high-quality seam;
reassembly;

DropXPress is not inherently a Click-lock. The connection profile consists of two L-shaped hooks. The hitch is held due to the weight of the laminate panel and the friction force, since the lowering of the board at an angle of 0 ° from top to bottom occurs with an interference fit.

This method has its advantages:

increased laying speed;
ease of installation
the same locks for the end and the long part

PressXPress- mounts with a counter-element, included in the new generation of 5g. When the board is seated in the groove, the fastening element is displaced, which is driven into the recess. Thus, the effort required for installation is minimal.

Advantages of the castle:

increased installation speed;
strong connection;
invisible seam;
possibility of installation at any angle.

In 2017, a new connection was presented at Domotex FitXPress, which will be used on Balterio's Magnitude Series laminate flooring, replacing PXP. The difference between the locks lies in the shape of the latch tongue.

Megaloc

Used on Classen laminate. It is a modification of the 5g system. Replaced the outdated EasyConnect model. The locking tab is located in the groove, not on the tongue. Just like on the Pergo coating, wax impregnation is used for moisture insulation.

Installation is carried out in separate panels, and not a whole row at once. Boards are laid at an angle until they click. Work can be done alone without outside help. If necessary, disassemble the connection is not difficult.

T-lock, 2-lock, TC-lock

Featured by Tarkett

T-lock- the old technology is satisfied, at the moment it is quite common, but it is being replaced by modern systems. It has a relatively small joining angle of panels of the order of 20-25°.

Laying may require the participation of several people, since it is necessary to mount the panels in rows as a whole. At the slightest shift of one of the boards, you will have to disassemble the entire row and start the process again.

Of the minuses can be identified:

the joint is visible on the end of the laminate, especially in dark colors;
with repeated use, the lock along the long part of the lamella may be deformed.

2 lock- newer model. It has a plastic tab to secure the connection. Allows for quick and easy laying even by one person - the assembly is carried out not in a whole row, but in one panel.

TC lock is a T-lock receiver. It is becoming more widespread. The cost does not exceed its predecessor. Unfortunately, old collections cannot be docked with the new TC-lock system due to the height difference.

Perhaps this is the only negative, let's focus on the pros:

there is a tighter contact during coupling, therefore, the probability of moisture getting into the interlock is reduced;
very good strength characteristics - the level of tensile load exceeds the norm by 8 times;
quick and easy assembly;
one person can do the installation.

TwinClic

Represented by the Russian brand Kronospan. At its core, it is an analogue of T-lock. It is also not possible to lay one panel at a time - it is necessary to assemble the entire row, which is not always convenient, especially when the installation is performed by one person.

When fixing the board in the groove, there is no pronounced click. It is better not to use this type of lock for laying laminate with a solid floor throughout the apartment, since there is a possibility of raising the joints under loads.

On models of laminate, which is in a low price category, there is very little protection against moisture.

LocTec

Patented Witex laminate locking system. Refers to high-strength compounds. Fairly easy assembly allows you to work alone. The installation process should not be difficult. The result is a smooth floor covering without visible seams.

Docking points are impregnated with a special water-repellent mastic.

Alloc

Introduced by a Norwegian flooring manufacturer. The quality is up to the mark. Has an aluminum insert. It has excellent strength properties, so it is most often used on commercial grade 33 and 34 laminate, which is designed for laying in places with increased operational load.

The advantage in strength becomes especially noticeable in large rooms. For such places, it is possible to lay a laminate without thresholds over the entire area. For ordinary apartments, the installation of such a coating is not advisable, since the high price exceeds the benefits that are not destined to be revealed at home.

Lock processing

Most modern laminate models are protected from moisture in the form of impregnation of the interlock with wax, paraffin, and special mastic. If for some reason you have purchased panels that are not subject to this procedure, then you yourself can perform simple manipulations that will increase protection against moisture.

Such formulations are available in liquid or paste forms. Of particular difference is what consistency you choose. The main thing is that you feel comfortable using the composition.

Advice: if possible, it is worth buying a laminate with protection of locks from moisture.

You can also use sealant to join the panels. In this case, several positive effects can be observed:

increased protection against moisture;
a tighter connection is made;
if necessary, you can mask the seams.

Modern laminate models are equipped with convenient locks that allow you to perform a high-quality joint. In addition, most of them have water-repellent properties and do not need additional processing.

Experienced craftsmen perform installation for any system without loss of connection quality. If you are a beginner, then when choosing the type of laminate locks, preference should be given to models from the 5g generation with a fixing polymer tongue. In this case, laying will be carried out quickly and easily even alone.

2013-01-04

We will reveal all the technical characteristics and advantages of this unique system.

First of all, let's pay attention to the methods of installing flooring with Lock UNICLIC (unilin). The fastest installation method is considered to be connecting the panels at an angle. This method does not require an additional set of tools, which greatly speeds up the laying of the flooring. First, the short sides of the coating are attached to each other, and then the long ones. In hard-to-reach places, as well as in laying the last row of panels, you will need a hammer and pad. It will be necessary to connect the panels in a horizontal plane with a simple tapping. The choice of one of two laying systems for laminate or parquet with UNICLIC makes the system unrivaled and unique.

UNICLIC also characterized by the absence of gaps at the joints. Consequently, the surface of the flooring will eventually be completely smooth and seamless. You will not see gaps at the joints due to the perfect interaction of the tongue and groove. A secure and durable click-to-panel connection is achieved with bevelled edges, and the absence of gap between panels ensures a seamless installation. The lower wedge-shaped edge of the groove provides stress distribution and protection of the connection from damage when pressing on the edge from above. The perfect connection is achieved by making the tongue and groove of the same material as the panel, which completely eliminates the deformation of the profile, which in the UNICLIC system fits on all four sides of the panel. Thanks to the optimal adhesion of the panels and the perfect panel technology, the system has a huge advantage.

It should be noted that the click-to-panel system ensures that there is no difference in height during installation. During the installation of panels in a horizontal plane, only the lower edge moves, other sections of the profile remain motionless. The coating is easy to install even for a non-professional. The place from which you want to start laying, the angle or direction can be chosen at your discretion. The cover is very easy and convenient to install.

Another unsurpassed advantage of UNICLIC is its safe reinstallation. You risk nothing by moving from one house to another. Removing the flooring is just as easy as installing it. The click connection system will not be damaged. The plastic edge provides ease and simplicity in connection and separation of panels. There is a risk of breaking the profile and reducing the adhesion of the coating if we talk about a different click connection system. In this case, ugly gaps form between the panels. But the UNICLIC system guarantees the absence of such a problem.

It's safe to say that UNICLIC technology reliable. The Quick-Step production line is characterized by a special approach and tight control. Connections are constantly tested for strength, watertightness and rupture. Quick-Step flooring is one of the most reliable in the world thanks to constant quality control in production, as well as the latest technology.
All of the above qualities of the UNICLIC system allow us to call it the number one system among locking systems. No other system can compare to the click-to-panel connection system. Therefore, for the first purchaser or first installr, the company provides a lifetime warranty.

Laying laminate Kyiv- buy a laminate in our stores and we will install a laminate or parquet board for free, we will bring and install a plastic skirting board for free. Savings in person.

Parquet board:

VIDEO of flooring installation with UNICLIC lock

Installing MDF skirting boards is not an easy task. This is due to the fact that for them there is no special fittings that would connect the two strips in the corners, so they must be cut to each other end-to-end. It’s worth saying right away that “by eye”, it is very problematic to perform such an operation without a special tool. In most cases, the installation of wooden skirting boards is entrusted to professionals who have all the necessary equipment and extensive experience.

Laminate installation instructions, like the instructions for any other technological process, it consists of several important sequential points, adhering to which you can pretty well install the floor covering yourself. These items look like this:

Vinyl flooring is gaining more and more popularity. And no wonder, vinyl flooring is simply stunning with its richness of colors and patterns, ease of maintenance, high water resistance, durability of the material and its low price. One of the most popular and, perhaps, the most convenient in laying is vinyl floor ALLURE FLOOR- self-adhesive coating, high strength and with excellent aesthetic decor. It is about the procedure for laying this vinyl coating that we will talk with you.

natural cork in our country is relatively new, and therefore not well known material for flooring. Many compatriots treat this product of modern progress with some degree of skepticism. Although people who have already tested the environmentally friendly cork in action unanimously confirm the presence of all the declared technical characteristics in this coating.

Independently carrying out various repairs in your own home is a complex, painstaking process and for some people completely unfamiliar. A selection of video installation of laminate, parquet and MDF panels on the wall, ceiling can serve as a visual aid not only for beginners, but also for those who consider themselves professionals. These lessons reveal the small nuances and tricks of laying flooring (how to quickly lay a laminate on a wall without resorting to wet plastering technologies, etc.).

At present, adhesive laminate has practically disappeared from hardware stores and markets. , laid in a floating way, is represented by a huge number of options. When you are trying to navigate this abundance, do not forget - the quality of the locking system must be paid close attention. After all, it depends on it how your floor will withstand constant loads, how long it will retain the look that it had the first time after laying. We list the most outstanding locking systems - the development of leading manufacturers of laminate flooring.

The Uniclic lock is the most advanced patented locking system created by the developers of the world famous Quick-Step concern. The lock is latched. When laying laminate, there is no need to use any tools. The tongue and groove design on the sides of the panel allows for two mounting methods. Two adjacent panels can be connected at a slight angle - even less than the standard 45 degrees. Or, with its almost complete absence - that is, one panel, as it were, slides into another. This ensures the elementary assembly of the laminated coating - you yourself choose how it is more convenient for you to connect the panels in this particular case. Laying can start from anywhere and be carried out in any convenient direction. The Uniclic lock is located on all four sides of the panel, so that the strength of the connection of the panels will be the same both on their longitudinal sides and on the end. The connection looks almost seamless. There is no gap between the panels, as there is simply no room for them to move. Only for this locking system, the manufacturer gives a lifetime warranty (during the initial installation, the quality of the connection of the lamellas and the absence of gaps and divergence of the panels are guaranteed). The T-Lock (Tarkett Lock) is an exclusive development of the TARKETT company, for which a patent has been received. This type of lock belongs to the category of Click-connections, the most progressive today. In general, it has a well-deserved reputation for not being too expensive, but for exceptionally high-quality products. In Europe, this is the most popular laminate - in the middle price category. This popularity is largely due to the quality of the locking system. Wide locking elements are connected when approaching at a slight angle, without deformations and distortions. At the moment of connecting the panels, a characteristic click is heard. There is a secure fixation. At the same time, if desired, the connection can be disassembled - without deformation of the lock, and assembled again (up to 3-4 times). A small connection angle is convenient because the laminate is very easy to fit in hard-to-reach places (under radiators, doors, etc.). After snapping, a constant voltage level is created that prevents the panels from coming apart even with a significant and irregular load. The quality of the lock is ensured by ultra-precise milling. T-Lock (Tarkett Lock) tensile strength is normatively defined in European standards ISO / DIS 24334 and is 800 kg / meter.

The LOC-TEC lock is a branded “accessory”. The force required to break the assembled Loc-Tec locking system must be greater than 1100 N/m. Thus, Vitex laminate will be good in rooms with the most intense traffic. The lock for decades ensures maximum stability of the laid laminate, the absence of distortions and deformations of the seams.

Articles

When you plan to renovate your home, you want to do it in such a way as to provide the maximum level of comfort for yourself and your loved ones. And what could be more comfortable than being able to walk barefoot at home - and so that the floor under your feet is always warm? If you choose laminate as your flooring, then this task is quite simply solved. You just need to take care of the installation of the floor heating system. Of all types of flooring, it is laminate that is most often laid in conjunction with "warm floor" systems.

Perhaps one of the main advantages of laminated parquet over natural parquet is its resistance to moisture. Natural wood is frankly “afraid” of contact with water, and owners of luxurious parquet or affordable parquet boards have to make constant efforts to prevent prolonged exposure to moisture on the flooring.

The topic of this article is directly indicated in its title. Repair in a city apartment or a country house, and the purchase of building materials as one of the stages of the process, is an extremely troublesome business. We offer you the opportunity to ease these chores. And also minimize your costs. Isn't this an attractive opportunity?

Before purchasing plumbing equipment for a new or renovated apartment, it is worth taking a closer look at the topic. Of course, to study the range of plumbing from A to Z, you need to spend a lot of time. But you can also get some useful information from our article.

According to experts, the plumbing market in Russia is more than 80% imported. And plumbing from China is presented on it in the widest range. It is China.

If you are faced with the task of choosing plumbing that you will install in your home for many years, we recommend that you first of all pay attention to plumbing from Germany.