In which direction to lay the laminate. Useful tips. How to lay laminate flooring lengthwise or across - choosing a laying method Laminate flooring is laid lengthwise or across

Modern floor coverings are available and diverse. Laminate in stores is presented in a wide range: various manufacturers, colors, a wide price range. The choice is easy to make, the main thing is to decide on your capabilities and desires. The difficulty arises later, when it becomes necessary to lay the purchased flooring and decide in which direction to lay the laminate.

Scheme of the device of the laminate board.

Calling specialists to work will cost a tidy sum, so you have to find the time and opportunity to update the floor yourself.

A little about the composition of the laminate

Laminate is a multi-layer flooring that is resistant to short-term exposure to moisture, sunlight and light physical exertion. The thickness of the panels can vary from 6 to 12 mm, the length and width can also be different and are selected depending on the size of the room and the desired pattern.

Laminate options.

Protection against external influences is achieved thanks to a durable film covering the panel from moisture and damage. The quality of the laminate as a whole and its cost depend on the thickness of the coating.

Under the protective layer is paper, with a certain texture or image. Coloring can imitate any natural surface, including stone, wood, sand. The main layer with the greatest thickness is fiberboard and resins.

The thicker and denser the fiberboard, the thicker and better the laminate.

Laying laminate yourself - choosing a direction

Before proceeding with the self-laying of the laminate, it is necessary to prepare the base. Preparation includes clearing the room of furniture, removing old flooring and cleaning up debris.

When the room is ready, you can purchase the material and leave it in this room for one or two days, during which it fully adapts to humidity and ambient temperature.

Any surface, including wood and concrete, is covered with a cork or polyethylene foam underlay, which serve as heat and sound insulation, making the laminate soft and creak-free when walking.

In which direction to lay the laminate is a rather controversial and ambiguous question. For example, if there is one window in the room overlooking the sunny side of the house, then the laying starts from the window towards the opposite side of the room, that is, along the sun's rays. This way of working allows you to reduce the visibility of the joints and make the floor almost seamless by reducing the shadow strip.

It is necessary to lay the laminate in the direction of light falling from the window so that the joints of the panels are not noticeable.

Also, the direction may depend on the way the laminate panels are fastened.

The locking connection with a latch is the connection of panels by snapping. This view requires careful preparation and measurement, if you make a mistake, it will be almost impossible to separate the panels.

It is desirable to start work from the far corner of the room in relation to the door, regardless of the location of the windows. Any type of coating is laid with a gap of 1 - 1.5 cm so that when temperature and humidity change, the material can freely increase and decrease in size.

First, the first board is placed on the floor, then the second board is snapped to the end of the previous one, and so on until the end of the wall towards the door.
Subsequent rows are mounted with a shift on half boards. That is, if there was a whole one in the first row, then at the beginning of the second, a laminate board sawn in half is laid. The second row of panels is connected again with the end side. Thus, two long panels are obtained.
Only when the boards are interlocked along their entire length can they be joined together. The first row rises slightly, connects with the second along the entire length and snaps into place. It is better to work with two or three people, so it will be convenient to lift the entire row at once, and you can achieve a minimum gap.
So, in a checkerboard pattern, row after row is placed until the floor surface ends. In the last row, there can be difficulties if the board does not fit in width. In this case, it is necessary to cut all the panels along, which is unprofitable from an economic point of view.

Some features of laminate flooring

Diagram of symmetrical laminate flooring.

The thorn-groove mount, if necessary, can be disassembled and moved to a new location. The elements are connected with the help of milk, with which they make their way to each other for strength and fastening density.

Glue locks are connected with glue and have an undeniable advantage: moisture resistance due to the ingress of glue into the seam. Among the shortcomings can be noted the duration of work and extra costs. Dismantling adhesive locks is impossible, so you need to carefully check your actions and think about each step.

If you have a warm floor, then using such an adhesive composition on top of it is unacceptable, as it can emit a pungent odor when heated. The laying technology is elementary: the ends of two boards are coated with glue and interconnected. Glue is needed special without the presence of moisture in the composition. It is applied in a small amount along the long and short sides of the panel, which will be combined with the previous ones.

Laying laminate is best to start from the window in the direction of sunlight. So the joints will not stand out against the background of the floor, and with an adhesive joint, the seams can turn out to be quite large, especially if there is no experience in this area.

The direction of laying the laminate can be absolutely any, including from the corner. Your idea or thoughts of the designer have the right to be realized. The direction diagonally can increasingly be found in modern houses and apartments. This technique is used to give the room a visually altered shape or to expand the space. Laying laminate from corner to corner is a complex process, and it is better to entrust it to professionals.

In any case, the main criterion for the work is the most dense connection of the boards to each other. No matter which direction you decide to lay the laminate, during long-term operation of the floor covering, even with thorough cleaning, litter gets into the cracks, as well as moisture, which further expands the junction and spoils the appearance of the room. The denser the panels are laid, the longer the coating will last.

Laying vapor barrier and substrates under the laminate

Scheme of asymmetric laying of laminate.

Vapor barrier is a special film that can breathe, but reliably protects against moisture and dust. If it is not possible to purchase it, then you can use the most common film used on the farm, for example, to cover greenhouses and greenhouses.

As for the substrate, it cannot be found from improvised materials; nevertheless, you will have to fork out and purchase it in specialized stores.

Most often, the substrate is produced in strips in rolls with a width of 1 m and a thickness of more than 1 mm.

When installing the substrate, there should be no overlaps, and the joints should be made as accurate as possible, without breaks. In order to avoid overlaps in the future, the joints can be glued with adhesive tape along the entire length of the strips.

If you have to lay the laminate alone, then it will be very, very difficult to connect several strips of the substrate at once. But there is a way out: first, one strip is laid in the same direction as the future floor covering, and then several strips of laminate are mounted on this strip of the substrate, then the next strip of the substrate and laminate, etc.

In which direction to lay the laminate does not play a significant role in the life of the floor. Much more important is the choice of high-quality material, the correct installation and laying of the substrate, the use of high-quality tools.

Of the tools you may need:

wooden hammer;
ordinary hammer;
hacksaw;
roulette;
marker.

For high-quality cutting of laminate, you can purchase an electric jigsaw, which will speed up the installation work.

Fulfillment of all simple requirements is the key to long-term operation of the resulting coating without changing its appearance and basic characteristics.

Laminate flooring has become one of the most popular due to its beautiful appearance, ease of installation and quite affordable price. A variety of color schemes and ways of arranging lamellas along, across and diagonally of the room give room for design solutions.

With self-repair, such a coating can be considered the most convenient for laying. Separate elements are interconnected with the help of special latches-locks on the edges. If you carefully follow the technology, it will take quite a bit of time, and the result will please.

Laminate layout methods

Depending on the type, color of the coating and the designer's ideas, various ways of placing the lamellas can be used. The visual effect largely depends on the angle at which the light coming from the windows falls. If you want to ensure that the coating seems monolithic, the lamellas are placed along the direction of the light.

This makes the seams less visible. Some types of laminate have a special chamfer that creates the appearance of separate boards. When using them, it is desirable, on the contrary, to emphasize the joints, placing them perpendicular to the lines of light.

It is also important to consider the shape of the room. By setting the direction of the slats, you can visually change the proportions of the room:

In a room with a regular rectangular shape, it is customary to lay the laminate along a long wall, from the window to the door.
In a long elongated room, it is better to lay the laminate across, as the transverse stripes visually expand the space.
If the room is irregularly shaped, laying the flooring diagonally will help hide this flaw. This method is somewhat more complicated - it will take more time and the consumption of materials will increase.

Advice! The direction of laying the laminate is especially important if a large area of the floor will be open: it will not contain furniture or carpeting. In small rooms, the free floor area is usually small, so it is worth choosing the most economical installation method that will have a minimum amount of waste.

Laying laminate along or across

Having decided on the direction of laying, you can count the materials. This is easy to do using an online calculator on the website of the manufacturer or seller. When buying a laminate, pay attention to the instructions available on each package.

Modern locks have a more perfect design, which greatly facilitates and speeds up installation. In addition, the service life of such a coating will be longer, so you should not save on quality. After purchasing a package of lamellas, they should lie in the room for several days in order to stabilize the humidity level. This will help to avoid deformation of the coating.

The most important step is the preparation of the subfloor. It must be dry and even. The deviation should not be more than 2 mm per meter. Any bump or depression will create a load on the joints, which can cause a creak or even breakage of the lock.

To properly prepare a concrete floor, you may need a self-levelling screed that will make the floor even and smooth without much effort. The wooden floor is usually leveled with 10 mm thick plywood sheets, which are fastened with self-tapping screws to the base.

A special substrate for laminate flooring must be laid on a flat subfloor. Its quality determines how comfortable and long the use of your flooring will be.

Substrate selection

The choice of material on which you will lay the laminate depends on:

will the floor creak?
how long will it last;
how loud footsteps will be heard;

will your feet be warm;
will there be any dents from the furniture.

Just like laminate, different types of underlay differ in quality and price. Often, flooring manufacturers will insist on the use of a specific underlay, and the validity of the warranty depends on this. This often requires the use of a specific material with a given thickness.

As a rule, the higher the quality of the material, the higher its cost. For an economy class laminate, it makes no sense to purchase an expensive substrate, since it will last longer than the coating itself. You will have to determine the golden mean yourself.

Let's take a look at the different types of underlay available on the market:

Foamed polyethylene in rolls, having different thicknesses, is most often offered as the most affordable option. It does not allow moisture to pass through, is quite elastic, has certain heat-insulating and noise-absorbing properties. Its main drawback is a short service life, after 5 years it becomes unusable.

Laying order

When the base of the floor is properly prepared, the materials are purchased and kept indoors, the flooring can be laid:

Advice! If you are laying the flooring yourself, study not only the instructions, but also a few video tutorials. This will help you avoid common mistakes.

Installing laminate flooring is a quick way to transform the flooring in a room. It can be laid both along and across, depending on the effect you want to achieve. If you want to save money, you can do it yourself by following the manufacturer's instructions.

It is no secret that laying modern laminate flooring is available to most of us even without practical experience. The only question that beginners may have before starting work is how to lay the laminate along or across? There are several opinions on this subject, and they will be discussed in the article below.

In the photo - a diagram of the direction of laying the laminate

The principle of laying laminated floor slats

Installation is carried out only on a flat surface. The installation instructions require that its difference is not more than 5 mm;
For some types of laminate flooring, an additional waterproofing layer of waterproofing film is required. At the same time, the installation price will, of course, increase;
The rough floor must first be cleaned of debris and wiped dry;
When installing a laminated coating with your own hands, do not forget about a special substrate. Its thickness should not be more than 5 mm, for lamellas with a thickness of 8-12 mm it should be 4-5 mm.

Tip: and the method of installation, depending on the class of coverage.

How to connect laminate lamellas

There are several clutch options for this:

glue method;
Lock method:

click;
lock.

Tip: If you don't know how to properly lay laminate flooring lengthwise or across, take professional advice - watch the natural light in the room during the day.

Laying the laminate along or across depends on the location of the daylight source. They can be a window or an artificial light source in a room without windows (corridor, hallway, pantry).

This is due to the fact that artificial or sunlight, when it hits the floor, which was laid perpendicular to it, illuminates the joints of the laminate boards and the floor may lose its attractiveness.

In this case, all connections between the lamellas will be clearly visible. Therefore, it is best to lay the laminate along the light source in the room.

Tools for installing laminate

An electric jigsaw or a hacksaw for metal, a wood saw will not work, as it has too large teeth that can ruin the decorative coating of the lamellas;

Metal ruler;

Large scissors, for example, tailor;

Sharp knife;

Nails;

Rope or fishing line;

Wooden wedges, bars;

Pencil;

Square;

Rubber mallet.

If there is no rubber, use a lightweight conventional hammer. Hit the ends of the lamellas only through the gasket.

Features of laminate installation using Click-locks

To assemble laminate boards, a lamella snap-in system is often used, which consists of collapsible locks. The mechanism is durable and resistant to mechanical stress.

The system is easy to install and has a long service life. This method of adhesion of the lamellas guarantees a minimum gap between them, although even it is visible if the direction of laying the laminate in the room is perpendicular to the artificial or daylight source in the room. So keep an eye on this if you want the floor in the room to look beautiful.

Laying sequence

Measure the width of the room. At the same time, consider a thermal gap of 8-10 mm near each wall, so you can create a "floating" structure. If the room area exceeds 12 m 2, the distance between the lamellas and the wall is calculated as follows: 1.5 mm per 1 m of the room length.

Calculate the width of the lamella in the last row along the wall.

Start installation from the far left corner. Lay the lamellas with a ledge to the wall.

Let's determine in which direction to lay the laminate. Lay out the slats along the source of illumination of the room, fixing them from the end with the locking method. In this case, the connection of the next row should be shifted by 300-400 mm from the previous one. So you can evenly distribute the mechanical load on the floor.

Connect the lamellas at a 45˚ angle, gradually lowering the laminate board until it clicks, which indicates the completion of the process.

Observe the subsequent installation, placing the lamellas in a checkerboard pattern, with the end connections offset, while not forgetting how to properly lay the laminate along or across, taking the light source as a guide.

Tip: If necessary, cut laminate boards to the desired width or length.

Features of mounting Lock-locks

The sequence of laying laminate boards with the Lock-system does not differ from the click-fixing system. The only thing is that the lamellas should be parallel to each other, and their engagement with each other occurs with the help of special grooves at the ends. Do not forget in which direction to lay the laminate, focusing on the direction of the light source in the room.

Features of the adhesive method

The main advantage of this method is the reliable protection of joints from moisture ingress. Thus, the service life of the coating is significantly extended.

Before laying laminate, let's find out its disadvantages:

complex styling;

glue costs;

panels after laying cannot be disassembled if you want to move them for installation in another room;

adhesive laminate is not used for underfloor heating.

During installation, water-repellent glue is applied to the ends of the flooring sheets.

The slats are connected according to the tongue and groove principle.

Tip: do not save on glue, and never use PVA. It is based on water, so it can cause swelling of the coating, which will violate the integrity of the connection.

Remove adhesive residue with a damp cloth.

After laying 3-4 rows, not forgetting in which direction to lay the laminate, wait 2-3 hours.

Then continue laying the surface to the end.

Use a crowbar when laying the last row. Work it carefully, without damaging the lamellas and the wall.

Tip: make a paper template in advance if the floor rests on the heating pipes.

Cut out all the necessary holes with a jigsaw. Do not forget about the thermal gaps between the lamellas and the wall, the lamellas and the door frame. To do this, use special spacer wedges.

Tip: After finishing the installation, remove them and hide the gaps under the plinth. Attach the latter to the wall, but not to the floor.

It should also be said that the installation of an adhesive-based laminate is a complex and time-consuming job. If you have not had this experience before, it is better to provide the installation work to specialists. Do not forget that this option for fixing the lamellas does not provide for dismantling the floor in the future.

A few more secrets

Laminate should always be laid long side along the light source.

If you want to visually expand a room, for example, a corridor where there are no windows, you can put the slats across.

If you know how best to lay laminate flooring, then apply the laying direction depending on the individual characteristics of the premises, as well as on their design. The main thing is that the light source should not contribute to casting a shadow between the connections.

Lamellas, laid perpendicularly - increase the width of the room, along - its length.

Conclusion

The article described in detail how to lay a laminate along or across the room, as well as what affects it. Then the joints between the lamellas are not striking, and the coating looks impressive and beautiful. In the presented video you will find additional information on this topic.

According to the manufacturers, due to the locking system of joints, the laminate is assembled easily and quickly. But there is a problem that arises when starting work: how to properly lay the laminate along or across the room? This issue can be solved using certain technologies.

How to properly install laminate

Having chosen the color and texture of the material for laying on the floor in an apartment or house, the owner usually does not think about the direction of laying the laminate. If you believe the experts, the direction in which the laminate is laid determines its durability and wear resistance. Proper laying of the laminate will create a certain decorative accent. Such a laminate belongs to the class of long finishing floor materials, because. its length is 4.5 times greater than its width. There is a limit to the laying options for laminate flooring.

In the light (from the window)

On the recommendation of flooring manufacturers and craftsmen, this installation method is optimal. If you lay a laminate in apartments with a standard layout in this way, you will get a smooth monolithic surface with barely noticeable joints.

A similar assembly is used for materials that have a double-sided chamfer. The surface is reminiscent of a plank floor in country or old Russian style. If there is texture embossing on the laminate, this will further emphasize the texture or give an aged look to the floor surface.

Laminate class 32-34 is suitable for installation in the light. Class 31 laminate should be used with care due to low wear resistance at the joints, and this leads to rapid wear and loss of appearance.

across the world

This assembly method is carried out perpendicular to the window and parallel to the long wall. Used laminate 32-34 class. Such installation allows you to make a visual increase in the room. Laminate flooring across the room highlights:

laminate texture “in register” (uneven embossed, bumpy surface imitating wood), “chrome effect” (alternating laying of glossy and matte stripes), “brush” (wood imitation, after processing with a metal brush), etc .;
U- or V-shaped chamfer on 2 or 4 sides;
3D drawing.

With perpendicular laying, the incident light highlights the joints between the lamellas, their texture, and gives the surface volume. Rooms with this arrangement of laminate have a special charm, as deep embossing and reflections give it a lively play of light and shadow.

Popular manufacturers have collections that combine different decors and sizes of laminated boards. Experienced professional craftsmen assemble textured lamellas of different formats into a harmonious and spectacular floor.

Along the way along the way

In passage rooms (corridor, hallway, hall) or in rooms with a certain direction of load (study, kitchen), laminate should be laid along intensive movement. This option is necessary so that the lamellas at the joints are less erased. In this case, class 31-34 laminate will last a long time.

Advice! It is impossible to lay a laminated coating across the movement, since the main lamella is erased more slowly than the edges, which halves the life of the parquet.

Diagonal decking

Masters are against such laying of laminate, but the client's desire is the law. In this case, the laminated board is laid at an angle of 40-60 degrees to the walls. This installation is used as a special design technique to change the geometry of the room or make the interior more interesting. This method is often used in rooms where window openings are located on adjacent walls.

Such a collection has certain disadvantages:

For this option, you need to choose lamellas of class 33-34 with a chamfer or a pronounced texture

Custom laminate flooring

Before choosing an assembly option, you need to pay attention to some features.

Unusual lamella size

In the collections of manufacturers, you can see not only long boards 30x200 cm. Lamellas are produced for the original flooring:

rectangular type 40x80, 40x120 cm, etc.;
square view 40x40, 60x60 cm.

This size is necessary to imitate a type-setting array or a palace (artistic) floor. The design of this parquet is great, and the assembly looks chic. Due to non-standard sizes and decors, when laying the coating, you can not adhere to the rules.

base base

Under the laminated coating, the best base will be a leveled and dried concrete screed. When assembling on a wooden base, the lamellas are mounted perpendicular to the base boards. When done correctly, the deflection of the floor is reduced to a minimum.

Laminate design

Radial sawing is an implicitly expressed textured surface that imitates wood. The resulting coating has almost no halftones. Lamellas are mounted in the direction of travel or in the light.

The lamellas of the tangential cut are characterized by the presence of dark stripes, knots, in some collections there is an embossing. Such strips can be mounted in any way.

Rustical slats combine tangential and radial sawing with the addition of imitation of a minor defect: cracks, blackening, abrasions, sharp color changes. This laminate looks aged. For a variety of coverage and maximum resemblance to a natural wooden board, the decor in the pack changes with an interval of 1:4 or 1:6. In this case, every 4-6 lamellas the pattern is repeated.

Not only its appearance, but also the durability of the coating itself will depend on how to lay the laminate, along or across the room, therefore, when choosing the laying direction, first of all, you need to think about the possibilities of the coating, and not the aesthetic appearance.

Laying laminate flooring in a hallway has never been an easy task. We are talking about the appropriateness of such installation, its technological difficulties, etc. Since all kinds of damage and moisture cannot be avoided, care must be taken to ensure that your laminate floor lasts as long as possible. What needs to be done for this?

Probably the main rule is to buy lamellas not lower. Such a laminate in the corridor will be subjected to frequent loads, BUT it can resist them. It will endure even the highest level of patency and will not change its appearance, even years after the start of operation.

! Yes, grades 21-23 are exclusively household options, but for such a room it is better to choose exactly grade 32. Of course, its cost will be higher, but the service life will reach several decades, and not 2-3 years.

So, how to lay laminate in the hallway? Many people ask this question, but not everyone knows the answer. The laminate floor in such a room is subjected to significant mechanical stress, so its installation has several important features:

Stack ONLY on a perfectly flat base. Level the floor as best as possible. Yes, in other rooms allowable differences are allowed, but in this one such a possibility must be excluded. Firstly, laying boards in such a room will be easier. Secondly, the deck will not sag or rise in the event of pressure on the panels;

! All this will help protect the floor from premature damage and wear. Please note that you can use both the adhesive version and elements with special locks.

certainly use . So the floor will be warmer, stronger, and smoother. We recommend cork or bituminous cork. It has the best characteristics and is suitable for lamellas of any thickness. You can find a cork in any specialized store;
to visually make the space larger, you can put the boards in a transverse version. The herringbone method is also considered a very popular method. It is more original, but not suitable for every design. The room will get bigger. But, in this case, it is also important to take into account one significant drawback: a large amount of waste - up to 15%.

So, in order for the laminate in a narrow corridor to perform not only a practical, but also an aesthetic function, it is important to follow a few simple rules:

Rule 1. For a narrow room, choose a light color scheme. As a rule, light pastels, blues and white-green tones are considered the best options, which visually push the boundaries.

Rule 2. Make several directional lines towards the expansion in the floor finish. Use mirrored surfaces that also expand the space. This is a fairly economical way to expand.

Rule 3. If you prefer darker and more saturated colors of the slats, we advise you to choose the right lighting for the room.

How to put laminate in the hallway? First, choose a quality substrate and lay it correctly. Many people prefer to connect the sheets of the substrate with tape. This is a positive point that prevents sheets from shifting. At the same time, in the event of an unexpected leak, all the moisture remains in the apartment, and does not spill onto the ceiling of the neighbors from below.

! If you live on the ground floor or in a private house, it is not necessary to connect separate sheets at all. But, the substrate should not move, then the flooring will be durable.

If you do not save on the substrate and choose high-quality material, there will be no gaps in the flooring after installation. Remember that such a layer, unlike lamellas, should be pressed tightly against the walls. In some cases, even go out to them. Later, this flooring is covered with a plinth and corners, which ensures reliability. Some masters also advise laying the substrate in a checkerboard pattern or perpendicular to the direction of the panels.

The process of preparing for laying laminate in the corridor includes two main points:

Careful preparation of the rough base, which includes cleaning the floor from dust, dirt and debris. For this purpose, you can use a vacuum cleaner. For moisture insulation, a vapor barrier film is used, on which the substrate is then laid. Such layers also serve as sound insulation;
taking into account the indentation from the walls by 10-15 mm. This is the so-called technical gap, which is necessary for cases of humidity differences and changes in the linear parameters of laminated panels. The distance left (gap) eliminates the possibility of deformation. Later, such gaps are hidden by a plinth.

Staged work with coating:

Stage 1 . Laying the first row. Laying laminate in the hallway starts from the wall. In this case, all the elements used are necessarily connected by ends. To keep the technical clearance uniform on all segments, you can use special wedges or pieces of the laminate itself.
Stage 2. The first board of the second row must be inserted with its side, pressing it against the board of the first row - a tenon in the groove. First, the second bar is attached to the end of the first. After that, both boards are raised at an angle of 30 ° and the second board is easily inserted into the board of the first row, with the long side into the groove. In exactly the same way, continue to mount the rest of the lanks. The last board is cut to the desired length, and its remains are used as the first element of the next row.
Stage 3. When you reach the last row of boards, be extremely careful. It must be cut so that the length completely covers part of the floor. When doing this, take into account the dimensions of the compensation gap.

During installation, be sure to use a sealant for seams. Its use will eliminate the possible ingress of moisture into the seams between the panels. And remember that styling can take a long time, even if the room is very small. The duration and complexity are directly affected by a large number of doors, pantries, niches, etc.

Corners and jambs

Separate boards need to be cut or special figured cutouts should be made in those places where they adjoin corners and jambs. This procedure takes more time. The result should be neat, so take your time. Today, even very experienced craftsmen believe that flooring in a narrow room is the most difficult task. The quality of surface preparation plays an important role here. It is on him that the accuracy of fitting the planks to all angles, the jambs, the protrusions depend.

heating pipes

Are there heating pipes in the room? Then be sure to make a curly cut.

Skirting board installation

Today, to visually expand the space, you can lay lamellas perpendicular to the length of the room. For narrow rooms, this is just perfect. At the same time, the space between the joints is about 20 cm - this is the condition, the observance of which guarantees an increase in the strength of the connection of the lamellas. Once you have completed the installation work, install the skirting boards.

! Remember that not to the flooring itself, but to the wall!

The wooden euro-plinth covers different gaps, depending on the configuration. It can be from 15 to 20 mm. If you prefer plastic options, then they are able to hide 18-21 mm.

It is very important to determine in advance the area of \u200b\u200bthe room on which the furniture will stand, and the one on which households, guests and even pets will most often walk. What for? It is better to cover such an area with a carpet or a small rug. So on the floor there will be less traces, and moisture. Be sure to lay the rug immediately at the entrance (at the front door), so all the dust, dirt and water will remain on it, and not spread throughout the flooring.

From excessive moisture, the laminate in the corridor will begin to deteriorate and swell. To prevent such negative consequences, during the rainy and snowy season, wipe your shoes dry before placing them on the floor. Or immediately put it on a special shelf. Then a presentable appearance of the flooring is guaranteed.

In general, all this will help to increase the operational life of your floor, which will retain its original appearance for a long time.

Video, laying laminate flooring in the hallway.